How to clean graphics card

How to clean graphics card

Graphics cards, like any computer component, can accumulate great dust. Over time, this dust can form a layer between the wings of the heat sink, interfering with its cooling capacity and overheating the graphics processing unit, or GPU. This can cause the card to slow down or shut down. Before doing so, clean the sink thoroughly. Once cleaned, the graphics card should perform normally, providing you with the graphics capabilities that your system needs.

Related Article: Best Graphics card for Hackintosh in 2022


  1. Turn off the PC and remove the power and monitor cable from the system. Open the case by removing the screws that hold the case cover in the body of the case. These patches are located on the back of the case. Slide the case backward from the front of the case and empty it from the body of the case.
  2. Find the graphics card in the back of the machine. The graphics card has a port for the monitor cable. Remove the screw that holds the graphics card and push the small lever under the card into the socket that holds the card. Carefully pull the card out of the socket; Keep it on a flat surface.
  3. Open the card’s sink, if it is covered, by removing the screws that hold the cover in place. Pull the cover free to reveal the heat sink. Remove the clips that hold the heat sink in the graphics card by pressing the clips on the bottom of the card together and pulling the heat sink post through the hole in the card. Carefully remove the heatsink from the card.
  4. Clean the thermal paste from the back of the card and the top of the graphics processing unit with a cotton ball.
  5. Remove any dust or debris between the small metal wings of the heat sink using a cotton swab.
  6. Moisten the cotton swab with rubbing alcohol. Clean the surface of the heat sink with a cotton swab to remove all traces of dust.
  7. Apply a small amount of thermal compound, the size of two grains of rice, in the center of the GPU. It is spread over the entire surface of the GPU using the edge of a piece of plastic.
  8. Replace the heatsink on the GPU, screw it firmly in place, and replace the plastic cover. Return the graphics card to its socket and screw it in place. Replace the PC cover, secure it with the case screw, then reconnect the monitor and power supply to the system.

There will come a point when you will need to wipe off the dust that has collected on your graphics card and other computer components, regardless of whether or not you had dust filters installed. But disassembling a graphics card in order to clean it can be a challenging task, particularly if you have no prior experience or if you don’t want your warranty to be voided. Educate yourself on improved cleaning techniques in this section of the site. It cannot be separated.

Disassembling a graphics card to clean it is not difficult, but if you do not have the necessary experience, materials (thermal paste), or do not want to risk losing your warranty (because many manufacturers cancel it if you have to fix it (you have to fix it on top), you may leave that almost perfect (except that there will come a time when you will have to change the thermal paste too).

How to clean graphics card

Supplies and equipment needed

If you want to wash the charts before dismantling it, you’ll require three: a can of pressurized gas, quasi baby wipes (which we don’t want to leave on the charts), and ear brooms.

How to tidy up a graph without having to separate it into two parts?

When cleaning between the graphic cpu heatsink sheets, it is always best to start with a compressed air can since this is what will be utilized to eliminate the large majority of dirt and, in particular, the eyeliner that has collected between the sheets of the graphics heat sink.

If your video card is of the blower variety, avoid using pressurized gas on the rear of the video card (where the video outputs are located), as this will merely force the dirt back into the card. Instead, you should aim towards the fan’s edges, which will allow air to enter the fan more readily. As long as you follow the instructions carefully, you should have no trouble getting all of the dirt out from under the graphic.

Step 01:

Apply pressurized gas above to enable dust to flow from the bottom of your graphic if it is not a shredder type but has normal wings instead. Make sure to cover the entire image in order to try to drop it safely. It should be applied to the horizontal portion of the sentence. Disinfect everything with a disinfectant solution. This is the interior of a sink.

Step 02:

The next step is to thoroughly clean the area of the graphic with damp wipes, paying particular attention to the fans and, in particular, the bottom, where dirt tends to collect. To do this, wipe your fingers across the fan blades, taking care not to bend them too much. Because the foam is flexible, it makes no difference if they flex a little bit. However, you must be cautious not to flex them too much or they will break.

Step 03:

Using gunk to wash the grills on the rear of the graphic, especially if it is a blower-style graphic, is the final step. If you choose, you can lightly mist the bushes with isopropyl alcohol before removing the grid from the area with pressurized gas. However, this is not required because the grid is simply being removed to remove any dirt that has lingered on it after being removed with compressed air. ۔


With these three procedures, you might have realized that washing the video card without disassembling it is a simple task that should be performed at least every 6 months, if not more often. When your graphics card is no longer under warranty, replacing the warm compress is a time-consuming (but not difficult) task that can be left alone for up to two years without causing any problems.

James Hope
My name's James and throughout the long term. I have actually assembled numerous PCs for me as well as my companions. I love gaming, programming, illustrations planning and essentially whatever has to do with PCs and innovation.