How to properly remove and place back the Ram sticks?

How to properly remove and place back the Ram sticks?

If you already have RAM memory modules installed in your system and you wish to remove them in order to replace them, the process is even simpler in the reverse direction. Remember that all sockets have at least one active anchor per module and that in order to remove the memory module, you simply need to press the anchor down and out, which will release the memory module.

In the event that you have active anchors on both sides, you must do both, and you must be careful since the rim “jumps” when the anchor is opened, making it advisable to grip the RAM with one hand and remove it. Provide Anchor with a second. Alternatively, if the RAM does not “pop” after the active anchors have been released, slide the RAM upwards to get rid of it.

Ready. Clearly, inserting and deleting memory from a computer is a simple operation. However, if you have never done this before, you will need to take certain precautions to ensure that nothing goes wrong during the process. This is actually the simplest step when it comes to PC assembly, as you may already be aware, and it is equipped with a system that even the most experienced users can complete in a matter of seconds. Just make sure you’re moving it in the appropriate direction and, of course, that you’re using RAM that’s compatible with your computer’s specifications.

Check that you have the right type of RAM.

It seems like a brainer, but the first thing to do is to make sure you have the right amount of RAM installed on your PC. Modules can be DIMMs if they are desktop or SO-DIMMs if they are portable, and the difference in size is obvious. But between DDR, DDR2, DDR3, and DDR4 DIMMs, despite being the same length, there is a physical difference that you can see at first glance where the “mark” is located in the area of ​​the connectors. Also in DDR4, the area of ​​the connectors is slightly curved.

Check the type of anchor on your motherboard.

It is necessary to determine what form of anchoring the RAM socket on your motherboard is used as the following step. There are two sorts available: those with an “active” anchor and those with an “inactive” anchor. In the image below, active anchors are shown on the left, and inactive anchors are shown on the right. There are motherboards that are moving on both sides, but there are also numerous motherboards that are the same on both sides, as seen in the illustration. Motherboards with passive anchors on either side will not be found under any circumstances, because there must be a retention mechanism for RAM memory, which ensures that a motherboard will not be damaged if the RAM memory is accidentally erased. Once the bar is in place, the modules will not be able to move out of their original positions under any circumstances.

They vary in that they have a moving part that links the module to the socket, whereas passive anchors do not have such a section and are therefore non-functional. Make sure that the active anchors are open before you begin installing RAM. To accomplish this, we just pull out the anchor and the door will open.

How to install RAM memory modules in your PC.

Following the completion of the necessary checks, we will examine the process of installing RAM memory on the motherboard. In order to achieve the best results, line the RAM module with the socket and lay it on top of the socket, first on one side and then on the other, and press down until you hear a little “click.” This is the optimal strategy. As a result, active leeches have already gained access to the memory module and are holding it hostage. In the event that these anchors fail to shut down, we do not attempt to repair them.

The RAM must be inserted through the passive anchor component if the motherboard is one of those with an active and inactive anchor, so that the memory module recovers when the Active button is pressed. If the motherboard is one of those with an active and inactive anchor, the RAM must first be inserted through the passive anchor component. If the motherboard is one of those that includes two active anchors, we will be able to erect the module without any additional steps. We first position it on the platform, and then we press both sides at the same time, ensuring that both anchors are securely closed.

Whichever anchor you choose to use, you must exercise caution not to place too much pressure on it. We believe that each module should be easily inserted, and that you only need to apply a certain amount of pressure as long as you do not hear the “clock” anchoring system when the case is closed; however, we caution you against applying too much pressure (and whatever pressure you apply, stand up and do not bend in order to avoid damaging the motherboard socket). It is possible to be damaged.


When it comes to installing a new RAM kit on your computer, it may appear to be a simple process, but if you’ve never done it before, you may encounter issues. Whether you’re replacing your existing RAM with a new one, expanding the existing RAM, or installing new RAM from scratch, we’ll teach you the proper approach to install RAM modules so that you don’t harm any of your computer’s internal components.

In fact, as you will see in the following section, installing or removing the computer’s RAM memory is the simplest and least dangerous of all the tasks that have to do with freezing the computer. However, with everything and with everything, you may encounter some issues, particularly if you are unfamiliar with what you are doing. Below, we will explain what you need to know and how to do it so that nothing goes wrong during the process.

James Hope
My name's James and throughout the long term. I have actually assembled numerous PCs for me as well as my companions. I love gaming, programming, illustrations planning and essentially whatever has to do with PCs and innovation.