How to remove cpu from motherboard

How to remove cpu from motherboard

Upgrading a computer’s processor, or CPU, is one of the most cost-effective upgrades to enhance PC performance. A CPU upgrade helps your PC boot faster, responds faster when performing multitasking, and speeds up web browsing.

You need to open the computer case to install the new CPU. Therefore, a basic understanding of the components of the equipment helps to simplify the process.

However, if you know how to use a screwdriver and can pay attention to detail, you can remove the CPU from the PC motherboard in a few minutes.


  • Turn off the computer. Disconnect the power cord and other cables from the machine. Move the computer to a flat work surface.
  • Use a Phillips screwdriver to remove the case screws from the back of the computer that secure the access panel cover. Slide the panel cover from the PC and place it in reserve. On some machines, you may have to remove the entire case cover if it does not have a panel that allows you to access the motherboard.
  • Slide the antistatic wrist strap on one arm. Clip the other end of the strap onto the metal surface inside the computer case.
  • Find the cooling fan above the processor. The cooling fan is usually about 2-3 inches wide and is located directly above the CPU. Once you have found the cooling fan, disconnect the cable from the fan assembly to the motherboard. This connection supplies power to the motherboard fan. Therefore, you must disconnect the cable before removing the processor fan.
  • Remove the clips or loosen the screws that secure the fan assembly to the top of the processor and motherboard. Depending on the type of processor and motherboard, the cooling fan connects to the processor socket in two different ways – clips or screw lock. To remove the clip on the processor fan, use your fingers or a screwdriver to squeeze the clips until you can lift the cooling fan and heat sink over the CPU. For fan assemblies attached to the screw lock mechanism, bend the four screws at the corners of the assembly approximately halfway to disconnect the lock. Once you have removed the screw lock, remove the fan assembly from the processor.
  • Lift the plate lever or processor lock lever into the CPU slot. On older motherboards, a thin lever arm closes on either side of the slot and opens the CPU slot. To unlock the slot, raise the lever arm. For newer types of processors, the loader board locks the CPU into slots. To unlock the slot, press the tab lock on the side of the CPU slot until the load plate is slightly raised. Lift the load plate until it interferes with the CPU.
  • Use your fingers to pull the CPU up and out of the socket. Set aside the age of the CPU.
  • Insert new processor into slot 8. Block the lever arm or load plate. Reverse the step used to remove the cooling fan assembly and open the case to complete the reinstall of the new processor.
How to remove cpu from motherboard

Why should you be careful when handling PC hardware?

As we mentioned earlier, hardware is not made of butter but all electronic components are fragile and must be taken care of. Be especially careful with bumps, scratches and falls, and of course it is recommended to “expel” yourself from static electricity first, as this can damage the components.

To do this, it is sufficient that you wear shoes with rubber soles and before touching any component, you should touch a piece of metal, such as the side of the box.

Similarly, as we mentioned earlier, no component should be forcibly inserted, and you should not use excessive force when disassembling it, all components have anchoring and non-anchoring systems which Make it easy to collect or remove.

PC components are easy to install or remove if you’re careful.

As you may have already seen, installing or uninstalling PC hardware is fairly easy unless you take some precautions such as removing yourself from static electricity and handling the devices carefully and Do not force or position them.

Keep in mind that all PC pieces, whatever the brand, are designed to work together and their installation is practically standard, so everything should fit snugly in place.

If a component does not fit perfectly, check the connections on both ends carefully as it is colliding with something without you noticing. We repeat, never force anything to fit and you will avoid problems.

Precautions when installing and removing each part of the PC

Making a PC is not complicated at all, especially if you have the practice, but with the right guide, even a novice user can build a good one over time. Of course, no one is immune to problems and inconsistencies, especially if the hardware is not handled properly, we will see one by one how to deal with each of them. ۔

Assemble or disassemble the motherboard in the PC case.

This is one of the most complex stages, but not because it is difficult, but because the twenty plates are an element of many dimensions.

When assembling the plate, you must insert the connector area diagonally, keeping the connector area down, and align them with the I / O shield, and then lower it in the opposite direction and drill holes into the anchor points of the screws. Compatible with

The trick to handling the motherboard is to hold it in an area that does not have the weight to bend the PCB, which is so long and wide that it bends relatively easily.

There are several options for this, ideally holding the ram socket with one hand (without rigidity, always with caution) and the other with the chipset heatsink area, as these are the two hardest and strongest places to go. Definitely stop tilting.


Installing a processor is not in itself very complicated, but the problem is that when it comes to installing it, the component itself is fragile. In Intel processors, just be careful not to touch the connection pin section, and be very careful

when placing the processor on the socket, as the socket of Intel motherboards is by far the most critical element. PC: If you leave the processor on top of the socket, in all likelihood you will have damaged the pin and you will have to replace the motherboard.

James Hope
My name's James and throughout the long term. I have actually assembled numerous PCs for me as well as my companions. I love gaming, programming, illustrations planning and essentially whatever has to do with PCs and innovation.